C919飞机全机静力试验技术

介绍了C919大型客机全机静力试验的目的及任务需求，分析了试验特点和难点。从试验飞机支持、试验加载及控制、试验测量及监控、损伤检测及状态监测等方面制定了总体技术实现方案，验证结果表明试验系统可靠，技术实现方案满足任务要求。试验中采用了多项创新技术：试验综合加载平台设计技术优化了多系统集成，加快了试验准备速度，降低了试验准备风险；约束点误差转移控制技术将约束部位误差转移至非重点考核部位，提高了关键考核区域试验精度；机身双层地板双向加载技术优化了机身加载及扣重设计，改善了局部载荷的加载精度。技术成果为后续型号试验提供了较高参考价值。     

Dynamic analysis of C/C composite finger seal

A seal device as an important component of aeroengines has decisive influence on per- formance, reliability, and working life of aeroengines. With the development of aeroengines, demands on the performance characteristics of seal devices are made strictly. Finger seal as a novel kind of sealing device, recently attracts more and more attentions in academic circles and engineer- ing fields at home and abroad. Research on finger seals has been extensively developed, especially on leakage and wear performances under dynamic conditions. However, it is a pity that the work on finger seals has been limited with a single approach that is improving the performance by structural optimization; in addition, the technology of dynamic analysis on finger seals is weak. Aiming at the problems mentioned above, a distributed mass equivalent dynamic model of finger seals considering the coupling effect of overlaid laminates is established in the present paper, the dynamic perfor- mance of 2.5 dimension C/C composite finger seal is analyzed with the model, and then the effects of fiber bundle density and fiber bundle preparation direction on finger seal＇s dynamic performance are discussed, as well as compared with those of Co-based alloy finger seal. The current work is about dynamic analysis of finger seals and application of C/C composite in this paper may have much academic significance and many engineering values for improving research level of finger seal dynamics and exploring feasibility of C/C composite being used for finger seals.     

基于8051的激光散斑控制器

针对激光显微成像出现的散斑,提出在光线光路中振动光线控制散斑的方法。具体以8051芯片为处理器,控制AD9850-DDS芯片产生不同频率的信号,并用ULN2003增强输出,控制固定在音圈电机上的多模光纤振动,最后通过CCD所采集图像散斑对比度验证方法。利用上述方法得到结论:在将设计的散斑控制系统应用于激光显微成像,控制频率为50Hz时,采集图像的散斑噪声获得最小值,并且采用40X显微物镜实现了CD-R盘片的高分辨激光显微成像。     

高温长期时效对一种镍基单晶合金拉伸和持久性能的影响

研究了高温长期时效对一种镍基单晶合金在室温条件下瞬时拉伸强度和在950℃/240MPa条件下持久性能的影响。结果表明:1000℃短期时效100h,合金室温拉伸强度σb与屈服强度σ0.2与时效前相比没有明显变化,时效超过500h后σb和σ0.2开始显著下降,时效超过1000h后,σb和σ0.2随时效时间延长下降幅度减小;短期时效100h和500h样品在950℃/240MPa条件下的持久寿命大幅度降低,延伸率快速上升,时效时间超过1000h后,持久寿命的下降幅度减小,合金的持久寿命与延伸率均趋于稳定。长期时效后γ'相形貌改变及γ/γ'相界面高密度位错网的破坏是时效后合金室温及高温持久性能持续降低的主要原因。     

S形蒙皮零件成形工艺

通过运用S3F软件对S形蒙皮拉形过程进行模拟仿真分析,评估S蒙皮拉形工艺性;预测拉形过程中将产生的缺陷;制定合理工艺方案;优化零件设计和模具结构;实现了该蒙皮零件在数控蒙皮拉伸机上的拉形。     

Statistical characterisation of spread F over South Africa

The occurrence of mid-latitude spread F (SF) over South Africa has not been extensively studied since the installation of the DPS-4 digisondes in 1996 and 2000 at Grahamstown (33.32 °S, 26.50 °E) and Madimbo (22.38 °S, 30.88 °E) respectively. This study is intended to quantify the probability of occurrence of F region disturbances associated with SF over South Africa. A study was conducted using data for 8 years (2001–2008) over Madimbo (with a time resolution of 30 min) and Grahamstown (with a variable time resolution of 15 and 30 min). In this study, SF has been classified into frequency SF (FSF), range SF (RSF) and mixed SF (MSF). The SF events were identified by manually identifying ionograms showing SF and tabulating them according to type for further statistical analysis. The results show that the diurnal pattern of SF peaks strongly between 01:00 and 02:00 local time, LT (LT = UT + 2 h), where UT is the universal time. This pattern is true for all seasons and types of SF at Madimbo and Grahamstown in 2001 and 2005, except for RSF which had peaks during autumn and spring in 2001 at Madimbo. The probability of both MSF and FSF tends to increase with decreasing solar activity, with a peak in 2005 (a moderate solar activity period). The seasonal peaks of MSF and FSF are more frequent during winter months at both Madimbo and Grahamstown. In this study, SF was evident in ∼0.03% and ∼0.06% of the available ionograms at Madimbo and Grahamstown respectively during the 8 years.     

基于DSP2812的三相SPWM波形实现

针对变频技术的核心—SPWM波形的产生和控制,详细介绍了SPWM波形的产生方法,并给出了软件编程。通过以DSP芯片TMS320F2812为核心,利用规则采样法产生SPWM波形,具有速度快,精度高,实时控制能力强,易于频率变换等优点。     

多通道智能场强计的研制

介绍87C51单片机在研制多通道场强计中的应用情况以及软件和硬件的研究设计。     

电机瞬态转速测试

介绍了一种利用单片机和光电转速传感器来测量电机瞬态转速及电机转速变化过程的方法。该方法简单、反应时间快、准确度高。     

一种便携式多通道精密测温仪

介绍了利用数字式温度传感器 DS1 6 2 4构成的多路温度测量仪器。它具有线路简单 ,测量精度高的优点 (在 - 5 5～ 1 2 5°C内 ,精度优于 0 .0 5°C) ;带有计算机接口 ,能够实现长时间连续测量。